BATTERY HOLDER "UNDERENGINE S1" A solution for all those who no longer want their large battery in plain sight. The suspension of the battery box is done at the rear axle of the engine mount. Additionally, 2 rubber buffers serve as supports to brace the battery box against the oil pan. 2 rubber grommets are used for cable routing. 2 tension springs hold the lid. Easy installation. Universal mounting materials included in the delivery .Important notes: Main stand must be removed Specifically designed for small batteries, e.g.: cs-batteries Batteries must be insulated by the customer (rubber mats) Material: 1.4301 (stainless steel) surface shot-blasted Width (internal measurement) 179 mm Height (internal measurement) 83 mm Depth (internal measurement) 98 mm Larger battery boxes available upon request!BATTERY HOLDER "UNDERENGINE S1" Stainless steel shot-blasted for BMW 2-valve boxer /5- /6 - /7 R 45, R 65, R 65LS `78 - `84 R 65, R 80, R 80RT, R 100 RS, RT - All Monolever models from `85 R80G/S, R80ST, R80GS, R100 GS, R80R / 100R and Mystik

Bosch Multifunction Relay / Load Relay 5-pin, 12 V Mini relay without holder and diode, with resistor Technical Data: Rated current: 30 A Rated voltage: 12 V Number of poles: 5-pole Relay function: Load contact Temperature range from: -40 °C Temperature range up to: 85 °C Housing type: Plastic housing Protection class: IP5K4 (housing) / IP20 (connector) Resistance: 90 Ohm Dimensions (LxWxH): 281 x 281 x 368.5 mm Technical Data:Voltage: 12 VNumber of poles: 5 Switch function: Normally open Load capacity: 30 AWith holder: No

Holder for Carbon Brush  

JMP Carbon Brush   - All phases of production are strictly monitored (from raw material to finished product) - Compatible with industry, OEM/OES in form, fit, and function - Highest quality standards (e.g., ISO certification) - OEM specifications are met and/or exceeded - All products undergo rigorous validation before being released for the aftermarket

Ignition Contact

Rubber mount set for diode plate  

  O-Ring   Attention: 2 pieces are required!Technical Data:Range:   No Inner Diameter:   100 mmOuter Diameter:   108 mmHeight:   4 mmMaterial:   Rubber Shape:   round

HELLA Working Current Relay 5-pole, 12 V With 2 outputs Power Mini Relay With parallel resistor to the coil Closes the circuit between the power source and an electrical consumer Ideal for switching paired consumers Application area: main headlights, auxiliary headlights, horns, heaters, fan motors, power windows, climate and ignition systems, etc. Technical Data Connector design ID: B2 Wiring diagram: S6 Temperature range, max: 80 °C Load capacity (at +80 °C) closing contact Ohmic load: 40 A Inductive load: 30 A Capacitive load: 30 ATechnical Data:Voltage: 12 VNumber of Poles: 5 Switch Function: Normally Open Load Capacity: 40 AWith Holder: No

Lock nut including wave washer   Stainless steel   Dimensions: - Outer: 19.5mm - Inner: 4mm - Height: 14mm  

JMP Skan Monitor 2 Lithium Battery monitoring with your smartphone: With the JMP Skan Monitor 2 and the new free Apple or Android app "JMP BatteryMonitor II", you can quickly and easily check the charge status of your battery. Only with a consistent, positive charge status of the battery is the full capacity and usability guaranteed. The positive charge status also prevents potential early damage or failure of the battery. Continuous recording captures the battery's charge status during rides and can be accessed later. The file with the data can be sent via email from the smartphone and displayed in Excel. This allows you to quickly identify where the charging voltage dropped or was too high. Additionally, a defective regulator can be quickly identified. Furthermore, the new app can also accurately check starting processes (starter, cable connections, etc.) and charging processes (alternator, cables, etc.). This saves long troubleshooting in case of problems. In case of low battery status or other issues, a notification can warn the rider depending on the settings in the app options. After a simple connection using eyelets to the battery and downloading the new Android or Apple app, the current voltage value can be retrieved. Please note: The transmitter is suitable for 12 V batteries and is only suitable for lithium batteries! The new JMP Skan Monitor 2 requires the new free app "JMP BatteryMonitor II"! Please download the free app from the Apple App Store or Google Play Store under JMP Battery Monitor II. The connection is made via Bluetooth. (Only from Bluetooth 4.0; e.g., from iPhone 4s, iPad3, or iPod Touch 5). The range is approximately 10 meters. Features: The JMP Skan Monitor 2 is excellent for detecting overvoltage > 14.9 V from the alternator before damage to the battery occurs. If the minimum voltage is not met, a reminder for soon recharging the battery is given. Easy attachment using eyelets to the battery. Power consumption is only about 2 mA. No damage occurs to the transmitter or battery in case of reverse polarity. Download the free app from the Apple App Store or Google Play Store under JMP Battery Monitor II. Voltage recording even during rides, results can be sent via email (file display in Excel possible).

  Clip