200/55ZR17 (78W) TL Rear Tire Bridgestone S22
€251.46*
Bridgestone Battlax S22 Optimized wet grip and cornering speed without sacrificing mileage Technical Data:Width: 200 Aspect Ratio: 55 % of widthConstruction: R (Radial tire) Rim Diameter: 17 inchesLoad Index: 78 Speed Index: (W) >270 km/h Profile: S22 Manufacturer: Bridgestone Whitewall: No Tube Type: TL Reinforced: No Tire Type: Summer tire
Airchannel on the Front Fairing BMW M 1000 RR MY from 2023 street
€289.90*
The Airchannel on the Front Fairing BMW M1000RR 2023 street in carbonfiber for the BMW M 1000 RR 2023 is a direct replacement for the original component.This part contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts. Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance. TÜV Approved Quality
Airchannel on the Front Fairing BMW M 1000 RR Racing MY from 2023
€199.90*
The air channel connects the upper fairing with the airbox. It is needed for a correct fitment of the upper fairing and also to ensure that the ram air can work correctly.
For our carbon we only use prepreg fabric specially produced for this purpose. which is also used in a similar form in Formula 1 and space travel. The material. which is elaborately hand-laminated and cured in several stages in the autoclave. not only impresses with its unique appearance but also with its unique technical properties. With the same volume. it has a specific stiffness three times as high as steel and at the same time. due to its particularly low density. only a fraction of its weight.
In order to optimally protect this high-quality material from all kinds of environmental influences. we are the only carbon manufacturer worldwide to use a specially developed plastic coating on all surfaces. In combination with our clear varnish. This ensures a previously unattainable and unique depth effect. which allows the high quality of the material to come into its own.
So that not only driving but also screwing is a pleasure. we only use the original fastening points for this part.
The facts
- with German ABE
- only for solo riding
- Sealing of all surfaces (inside and outside) with a unique coating to protect against environmental influences of all kinds
- Additional glossy clear lacquer coating on all visible surfaces - optimally protected against UV light
- Delivery ready for installation
- made of prepreg material specially produced for Ilmberger
- Manufactured in-house according to ISO 9001
- Attachment using the original attachment points
- quick and easy assembly
Airintake Channel BMW M 1000 RR / S 1000 RR MY from 2019
€169.90*
Airintake Channel fits to BMW S 1000 RR starting from 2019. and BMW M 1000 RRThis part is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts.Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.
Alcar Tire Pressure Monitoring System Sensor with Valve, Valve Diameter 11.5 mm for BMW R18
€79.90*
Universal programmable TPMS sensor, can be programmed via the diagnostic tool TECH350 (under accessories) or, even better, a clone of the OE sensor can be created. Valve diameter 11.5mm The battery life corresponds to the OE sensor and lasts at least 5 years
Alternator cover BMW S 1000 RR from MY 2019
€199.90*
Generator cover BMW 4 cylinder models since 2019
This part is a protective carbon piece and is mounted directly on top of the original component. For the mounting only original screwpoints are used. p>
In order to obtain a harmonious overall picture. the fiber layers are inserted and aligned in the mold by experts. The carbon part fits perfectly into the surrounding shapes of the motorcycle. The more of our parts are installed and combined. the more overwhelming the result.
For our carbon we only use prepreg fabric specially produced for this purpose. which is also used in a similar form in Formula 1 and space travel. The material. which is elaborately hand-laminated and cured in several stages in the autoclave. not only impresses with its unique appearance but also with its unique technical properties. With the same volume. it has a specific stiffness three times as high as steel and at the same time. due to its particularly low density. only a fraction of its weight.
In order to optimally protect this high-quality material from all kinds of environmental influences. we are the only carbon manufacturer worldwide to use a specially developed plastic coating on all surfaces. In combination with our clear varnish. This ensures a previously unattainable and unique depth effect. which allows the high quality of the material to come into its own.
So that not only driving but also screwing is a pleasure. we only use the original fastening points for this part.
The facts:
- Sealing of all surfaces (inside and outside) with a unique coating to protect against environmental influences of all kinds
- Additional high-gloss clear lacquer coating on all visible surfaces - optimally protected against UV light
- Delivery ready for installation
- TÜV certified quality
- made of prepreg material specially produced for Ilmberger
- Manufactured in-house according to ISO 9001
- Attachment using the original attachment points
- quick and easy assembly
Angled USB-C Standard Plug, 12-24V / 5V, max. 3A Cigarette Lighter and Onboard Network Sockets
€29.90*
For connection to cigarette lighter and standard sockets (e.g. BMW on-board network) via the 12 V on-board network of cars, trucks, buses, caravans, and boats for charging and operating devices such as mobile phones, smartphones, navigation devices, MP3 players, cameras, and all types of tablets that require a high charging current.- Connection: 1 x USB-C- with blue control LED for voltage indication- Protection against: reverse polarity, overload, overheating, overvoltage, short circuit
Badge - D = 27MM for example BMW R1200GS K25 RnineT F 650 700 800 GS 51142328447
€12.17*
Original BMW Spare Part
Additional Information
The part with the BMW part number 51 14 8 164 924 is used on the following vehicles:
Badge Holder left BMW S 1000 RR from MY 2019
€289.90*
Badge Holder left BMW S 1000 RR from MY 2019This part is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts.Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.
Badge Holder right BMW S 1000 RR from MY 2019
€289.90*
Badge Holder right BMW S 1000 RR starting from MY 2019This part is a direct replacement for the original component and contributes mainly to weight saving on the motorcycle (up to 70% less) and a higher stiffness of the parts.Like all of our carbon fibre parts. it was made according to the latest protocols and industry standards and can be considered to encompass all aspects of current 'best of industry' practice. The part is made completely out of pre-preg carbon fibre materials using an autoclave. As with all our carbon parts. we use a clear plastic coating that not only improves the appearance. but also protects the carbon fibre from scratching and has a unique UV resistance.
Battery Charger JMP Skan 1.06/12V 1A for BMW Motorcycles
€54.85*
JMP Battery Charger Skan 1.0 Microprocessor-controlled high-tech battery charger of the latest generation with 8 charging stages. Suitable for both quick charging of a battery and long-term maintenance charging, e.g., during vehicle winter storage. Suitable for: Standard Lead AcidGelAGMEFBLithium (LiFePO4) Technical Data: 6/12 V 1 Afor batteries from 2 Ah to 40 AhLow voltage detection: 0.7 VOvercharge protection, reverse polarity protectionSplash and dust proof (IP65)Dimensions: 180 x 80 x 40 mmWeight: 0.5 kgPower cable: 2 mConnection cable: 2.10 m Scope of delivery: 1x JMP Skan 1.01x Adapter cable with clamps1x Adapter cable with ring terminals for permanent connection to the battery
Battery Charger Motorcycle JMP Skan 4.0 12V 1A-4A
€71.69*
JMP Battery Charger Skan 4.0 CAN-Bus Microprocessor-controlled high-tech battery charger of the latest generation with 8 charging stages. Suitable for both quick charging of a battery and long-term maintenance charging, e.g., during vehicle winter storage. Suitable for: Standard Lead AcidGelAGMEFBLithium (LiFePO4) Technical Data: 12 V /1 - 4 Afor batteries from 4 Ah to 120 AhLow voltage detection: 0.7 VOvercharge protection, reverse polarity protectionSplash and dust proof (IP65)Dimensions: 190 x 80 x 50 mmWeight: 0.75 kgPower cable: 2 mConnection cable: 2.10 m Scope of delivery: 1x JMP Skan 4.01x Adapter cable with clamps1x Adapter cable with ring terminals for permanent connection to the battery1x Adapter cable for onboard socket (CAN-Bus)
Belly pan Racing BMW M 1000 RR / S 1000 RR MY from 2019
€699.90*
The bellypan of the BMW S1000RR Racing is part of the race fairing kit of the BMW S 1000 RR Racing since 2019. It is mounted via quick fasteners and not compatible with the original fairing parts.
It is only compatible with a full racing exhaust system. The lower fairing is closed and is suitable to catch up to 5L of fluids. In the front and the rear are holes which can be open when it’s raining.
A Carbonfairing is the lightest possible way of producing a fairing and protects the parts underneath on an extraordinary high level.
In order to obtain a harmonious overall picture. the fiber layers are inserted and aligned in the mold by experts. The carbon part fits perfectly into the surrounding shapes of the motorcycle. The more of our parts are installed and combined. the more overwhelming the result.
For our carbon we only use prepreg fabric specially produced for this purpose. which is also used in a similar form in Formula 1 and space travel. The material. which is elaborately hand-laminated and cured in several stages in the autoclave. not only impresses with its unique appearance but also with its unique technical properties. With the same volume. it has a specific stiffness three times as high as steel and at the same time. due to its particularly low density. only a fraction of its weight.
In order to optimally protect this high-quality material from all kinds of environmental influences. we are the only carbon manufacturer worldwide to use a specially developed plastic coating on all surfaces. In combination with our clear varnish. This ensures a previously unattainable and unique depth effect. which allows the high quality of the material to come into its own.
So that not only driving but also screwing is a pleasure. we only use the original fastening points for this part.
The facts
- racing part. not for street use
- improved cooling capacity for the brake
- better protection of the lower fork tubes
- Sealing of all surfaces (inside and outside) with a unique coating to protect against environmental influences of all kinds
- Delivery ready for installation
- made of prepreg material specially produced for Ilmberger
- Manufactured in-house according to ISO 9001
- Attachment using the original attachment points
- quick and easy assembly
Bellypan (1 piece) BMW M1000RR'23
€599.90*
The typical long Ilmberger bellypan made of high-quality autoclave carbon is also a must for the M1000RR. Thanks to special resin and integrated heat protection. the bellypan fits up to a few mm distance to the front muffler. The fairing looks more complete and the original exhaust more discreet.
For our carbon we only use prepreg fabric specially produced for this purpose. which is also used in a similar form in Formula 1 and space travel. The material. which is elaborately hand-laminated and cured in several stages in the autoclave. not only impresses with its unique appearance but also with its unique technical properties. With the same volume. it has a specific stiffness three times as high as steel and at the same time. due to its particularly low density. only a fraction of its weight.
In order to optimally protect this high-quality material from all kinds of environmental influences. we are the only carbon manufacturer worldwide to use a specially developed plastic coating on all surfaces. In combination with our clear varnish. This ensures a previously unattainable and unique depth effect. which allows the high quality of the material to come into its own.
So that not only driving but also screwing is a pleasure. we only use the original fastening points for this part.
The facts
- with German ABE
- Sealing of all surfaces (inside and outside) with a unique coating to protect against environmental influences of all kinds
- Additional glossy clear lacquer coating on all visible surfaces - optimally protected against UV light
- Delivery ready for installation
- made of prepreg material specially produced for Ilmberger
- Manufactured in-house according to ISO 9001
- Attachment using the original attachment points
- quick and easy assembly
Bellypan one piece street version BMW M 1000 RR 2021
€949.90*
The bellypan long version BMW M 1000 RR road replaces the original component using the original mounting points.
Attached in just a few minutes. the value of the motorcycle is thus increased again enormously. To achieve a particularly harmonious overall appearance. the fiber layers are inserted and aligned evenly in the mold by experts. In this way. the carbon part nestles perfectly into the individual surroundings of the motorcycle. The more of our parts are installed and combined. the more stunning the result.
For our carbon. we use only prepreg fabric produced specifically for this purpose. which is also used in a similar form in Formula 1 and aerospace. The material. which is laminated by hand and cured in several stages in an autoclave. not only has a unique appearance but also impresses with its unique technical properties. With the same volume. it has three times the specific stiffness of steel and at the same time. due to its particularly low density. only a fraction of its weight. These properties are particularly pronounced in our case. due to the high fiber volume content.
In order to optimally protect this high-quality material from environmental influences of all kinds. we are the only carbon manufacturer in the world to use a specially developed plastic coating on all surfaces. This. in combination with our clear varnish. provides an unprecedented and unique depth effect. which shows off the high quality of the material to its best advantage.
The kit is light as a feather and made of special heat-resistant prepreg to protect against discoloration caused by the intense heat on the pre-silencer. The generous cutouts also serve to dissipate the heat and the component is also provided with an internal heat protection film.
This Bellypan fits also on the S1000RR Models with the steel manifold.
The facts:
- With general operating permit (ABE)
- Sealing of all surfaces (inside and outside) by unique plastic coating to protect against environmental influences of any kind
- additional high gloss clear varnish on all visible surfaces
- optimal protection against UV light
- delivery in ready-to-install condition
- manufactured from prepreg material specially produced for Ilmberger
- Manufactured in our own production according to ISO 9001
- Mounting using the original mounting points
Bellypan Racing BMW M 1000 RR MY from 2023
€699.90*
The bellypan of the BMW M1000RR Racing is part of the race fairing kit of the BMW M 1000 RR Racing. It is mounted via quick fasteners and not compatible with the original fairing parts.
It is only compatible with a full racing exhaust system. The lower fairing is closed and is suitable to catch up to 5L of fluids. In the front is a hole which can be open when it’s raining.
A Carbonfairing is the lightest possible way of producing a fairing and protects the parts underneath on an extraordinary high level. The holes on the side support the hot air stream away from the watercooler.
In order to obtain a harmonious overall picture. the fiber layers are inserted and aligned in the mold by experts. The carbon part fits perfectly into the surrounding shapes of the motorcycle. The more of our parts are installed and combined. the more overwhelming the result.
For our carbon we only use prepreg fabric specially produced for this purpose. which is also used in a similar form in Formula 1 and space travel. The material. which is elaborately hand-laminated and cured in several stages in the autoclave. not only impresses with its unique appearance but also with its unique technical properties. With the same volume. it has a specific stiffness three times as high as steel and at the same time. due to its particularly low density. only a fraction of its weight.
In order to optimally protect this high-quality material from all kinds of environmental influences. we are the only carbon manufacturer worldwide to use a specially developed plastic coating on all surfaces. In combination with our clear varnish. This ensures a previously unattainable and unique depth effect. which allows the high quality of the material to come into its own.
So that not only driving but also screwing is a pleasure. we only use the original fastening points for this part.
The facts
- racing part. not for street use
- improved cooling capacity for the brake
- better protection of the lower fork tubes
- Sealing of all surfaces (inside and outside) with a unique coating to protect against environmental influences of all kinds
- Delivery ready for installation
- made of prepreg material specially produced for Ilmberger
- Manufactured in-house according to ISO 9001
- Attachment using the original attachment points
- quick and easy assembly
Biposto Seat Unit BMW M1000RR MY from 2023
€499.90*
The rear fairing for biposto riding. surrounds the pillion seat and allows a sporty look of the motorcycle even in operation with two persons. In combination with the SIA.009.M123S.K and the RHA. 011.M123S.K. the entire rear can thus be wrapped in carbon. while not excluding the eventual operation with a passenger.
If the motorcycle is to be returned even closer to its origins on the racetrack. the Monoposto rear fairing is the one to choose.
For our carbon we only use prepreg fabric specially produced for this purpose. which is also used in a similar form in Formula 1 and space travel. The material. which is elaborately hand-laminated and cured in several stages in the autoclave. not only impresses with its unique appearance but also with its unique technical properties. With the same volume. it has a specific stiffness three times as high as steel and at the same time. due to its particularly low density. only a fraction of its weight.
In order to optimally protect this high-quality material from all kinds of environmental influences. we are the only carbon manufacturer worldwide to use a specially developed plastic coating on all surfaces. In combination with our clear varnish. This ensures a previously unattainable and unique depth effect. which allows the high quality of the material to come into its own.
So that not only driving but also screwing is a pleasure. we only use the original fastening points for this part.
The facts
- with German ABE
- quick change between solo ride and ride with a passenger
- Sealing of all surfaces (inside and outside) with a unique coating to protect against environmental influences of all kinds
- Additional glossy clear lacquer coating on all visible surfaces - optimally protected against UV light
- Delivery ready for installation
- made of prepreg material specially produced for Ilmberger
- Manufactured in-house according to ISO 9001
- Attachment using the original attachment points
- quick and easy assembly
BMW Motorrad Schlüsselanhänger MLAR schwarz Schlüsselband
€15.00*
Artikelnummer: 76 61 5 A82 572Praktischer Schlüsselanhänger mit Make Life a Ride Schriftzug und großem, eingewebtem BMW Motorrad Schriftzug.ProdukthighlightsKleiner Make Life a Ride SchriftzugGroßer BMW Motorrad SchriftzugEckdatenMaterial: 100 % Baumwolle
BMW S 1000 RR XR 2019 Air Filter Sport Air Filter Racing Air Filter BMC
€103.41*
BMC Racing Filter In addition to the standard filter version, BMC has developed another type of filter. This is the "Race" filter, which maintains the same shape as the standard filter but is constructed from filter material that allows for increased airflow compared to other filter systems, while still retaining its filtering effectiveness. The BMC "Race" filter is designed for those who are not satisfied with the normal performance of their motorcycle but instead modify the engine and the control unit to achieve increased power. The "Race" filter can be recognized by a yellow stripe.
BMW S 1000 RR XR R Racing - JT 14T Sprocket 525 Pitch Fine Tooth INNER 26/30 HP4
€16.14*
Advantages of JT Racing Sprockets - Reduced weight due to the lightening holes- Made from high-quality Chromoly SCM420 steel for maximum durability- Perfectly suited for the sport-oriented motorcyclistTechnical Data:Pitch: 525 Mounting: Fine-toothed Inner diameter min.: 26 mmInner diameter max.: 30 mmInternal teeth (number of teeth): 13 Number of holes: without hole Width: 15 mmDesign: Weight optimized Racing Manufacturer: JT Number of teeth: 14
BMW S1000RR from 2019 Air Filter Replacement Filter BMC S1000XR from 2019
€68.84*
BMC Replacement Air Filter The acquired know-how from the racetracks is directly incorporated into the production of the series filters, to provide the demanding motorcyclist with a product that is tested, delivers performance, and is in a constant state of evolution. The materials used are the best currently available on the market. The filters are made from a single rubber frame to prevent any breakage. The filtering element is made from a special cotton fabric (4 layers), soaked in a low-tack oil. It is encased in an aluminum mesh that is treated with an epoxy solution to be resistant to gasoline vapors and oxidation. Additionally, the cotton has the advantage of being washable and reusable. Due to these features, the BMC sport air filters (replacement air filters) guarantee a higher airflow compared to the original paper filters, a minimal pressure loss of the incoming air, and thus lead to better engine performance. - Durability: washable and reusable, no replacement needed - Wider filter surface - Maximum air permeability (4 layers of cotton) - Higher absorption and filtration - Better pressure drop ratio - Tested by international testing procedures
Brake light switch / clutch switch OE for BMW F750GS F850GS + Adventure F900XR M1000RR
€84.04*
Vehicle-Specific Information: for vehicles with cruise control Brake light/clutch switch Original spare part
Brake Pad Sinter Front SA Brembo for BMW M1000RR M1000R K67 S1000RR from 2022
€50.24*
SA Sintered Metal Brake Pads for Front (SA) A sintered mixture specifically designed for front wheel brakes that offers improved braking performance under all operating conditions. An ideal alternative to OE brake pads for optimal performance on the road.
M1000RR
Welcome to the category for BMW Sport M1000RR spare parts & accessories!
Here you will find a wide selection of high-quality spare parts and accessories for your BMW M1000RR.
Our products offer you:
- Large selection of spare parts
- High-quality accessory items
- Top prices for every budget
- Easy ordering and fast delivery
Discover our range now and equip your BMW M1000RR optimally!
Order today and take advantage of our attractive offers!
Produktempfehlungen:
Tip
Action Bundle 2: Engine Protection *RALLYE EXTREME* + Crash Bars for Honda CRF1000L Africa Twin
€449.00*
With the RALLYE EXTREME engine protection for the Honda CRF1000L Africa Twin, we combine state-of-the-art manufacturing techniques with unique design to provide the best possible protection for the entire engine area of your bike! Under the toughest testing conditions, the RALLYE EXTREME engine protection has already proven its quality on the winning motorcycle of the Hellas Rally. The crash bar is made from high-quality, electropolished stainless steel and expands the usability of your adventure bike. Its special design ensures optimal force distribution and largely protects not only the radiator but also the tank and fairing from damage.The RALLYE EXTREME engine protection is designed for serious use with minimal weight. It takes on the functions of the engine crash bar.Note: Only in conjunction with the original header pipe
Tip
BMW Motorrad Jacket Moreno Connect GORE-TEX
€1,627.00*
Details
The
Moreno Connect GORE-TEX jacket combines a discreet look with excellent
functionality. The three-layer outer material keeps the jacket
waterproof, while generous ventilation options ensure an optimal climate. Back and joint protectors provide a high level of safety even off paved roads. The integrated heated vest can be controlled via smartphone or motorcycle. Active lighting on the back and sleeves ensures better visibility at night.Product HighlightsRobust, waterproof touring jacketOptimal ventilation through numerous zippers and AirVent insertsThree-layer outer materialSafety featuresNP2 joint protectorsNP Pro back protectorSafety FeaturesNP2 joint protectorsNP Pro back protectorFunctionalityTwo waterproof pockets on the front, one large pocket on the backCollar closure with VelcroInfinitely adjustable sleeve adjustment with VelcroStorm cuff at the sleeve hemsLeg closure with infinitely adjustable VelcroWaist adjustmentWaist adjustment, Velcro with diversionShort and continuous connecting zipperAdditional windbreaker in the jacket hem (similar to a winter sports jacket)Extra-large hanger loopIntegrated heated vestActive lighting on the back and sleeves for better visibility at night or in poor visibility conditionsWaterproof, washable, and integrated light guideTouch panel with on and off switchControl unit for operating the Connect functions of the heated vest and lightingControl unit can be connected to the BMW Motorrad Connected AppPower supply for the control unit via power bank or directly from the motorcycleThree inner pockets, one designed as a charging pocket for the smartphoneWaterproof up to a water column of 28,000 mmKey DataMaterial composition:Outer material 1: Layer 1 100% nylon, Layer 2 100% expanded polytetrafluoroethyleneOuter material 2 (insert): Layer 1 92% nylon, 9% elastane, Layer 2 69% nylon, 31% elastaneLining: 100% polyester
Tip
BMW Original T-Shirt RIDE Women's XL Red 76238561053
€12.00*
BMW Original T-Shirt RIDE Women's XL Red 76238561053
Size XL
Special Price - Clearance Sale
Fashionable sporty functional shirt, available as T-shirt or long-sleeve shirt
Functional material mix of 86% polyester, 14% cotton
Breathable, moisture-wicking, and odor-resistant
Side mesh inserts for increased air permeability, women's version with attractive print pattern
Cotton Touch: pleasant wearing feel like soft cotton
Decorative contrasting ribbon at shoulder seam
Flatlock seams to avoid pressure points
Women's cut slightly tailored, straight cut for men
Regular Fit
Material:
86% polyester; 14% cotton
Tip
Clutch Release Lever Clutch Lever for BMW R 850 1100 R RS RT GS 23131340829
€150.00*
Clutch Release Lever Clutch Lever
for R850 + R1100 transmission with clutch cable
Improved version
Due to numerous requests from you, we have searched for a solution to a common problem and developed this improved clutch release lever. It is mounted on the back of the transmission and accommodates the clutch cable.
Never again should your tour abruptly end somewhere in the middle of nowhere. The clutch release levers often break at the bottom of the transmission. Original spare parts are often unavailable. Therefore, we have manufactured a reinforced clutch lever from high-strength aluminum. We have increased the material thickness by about 30%. During the next transmission repair or clutch replacement, this lever can replace the original, reducing a critical point on your motorcycle. Alternatively, you can take it as a spare part (emergency tool) on your travels for emergencies. We have already saved some of you on vacation, trips, or tours with a DHL Express delivery. This option is, of course, also available. As roadside assistance, we ship spare parts, like this lever, as well as many other items, around the globe to help you. This lever corresponds to the BMW ETK part number 23131340829.
The lever 23 13 1 340 829 fits the following vehicles:
R 850 GS Type 259
R 1100 GS Type 259
R 850 R Type 259
R 1100 R Type 259
R 850 RT Type 259
R 1100 RT Type 259
R 1100 RS Type 259
NOTE: The original bearing sleeve and adjustment screw must be retained!
Tip
Repair kit for fuel pump quick coupling brass replacement for BMW R 1200 R GS RT
€34.95*
Repair Kit for Fuel Pump
Quick Coupling
Spare Part for
e.g. BMW R1200GS R1200R
R1200RT K1200 ....
This repair kit can be used to repair a leaking or broken connection on the fuel pump. The original screwed connections in the fuel pumps often have hairline cracks!
Quick, cost-effective, and easy installation.
Scope of delivery:
1 x Coupling nut part brass chrome-plated with shut-off, 3/8" NPT thread, fuel-resistant FKM sealFits:BMW R 1200 GS 2004-2012BMW R 1200 RT 2005-2013BMW R 900 RT 2005-2013BMW R 1200 R 2006-2013
BMW R 1200 GS Adventure 2005-2013BMW R1200 ST 2003-2007BMW R 1200 S 2004-2010
BMW K 1200 S K 1300 S 2003-2015
BMW K 1200 R K 1300 R 2004-2015
BMW K1200 R Sport
BMW K 1200 GT K 1300 GT 2004-2010
Important Notes:CPC recommends using:Teflon tape or liquid sealant for thread sealing!Tighten the coupling by hand and then tighten it with a wrench for a maximum of 1-2 more turns!Never screw the thread in completely!With tapered threads, only the first three threads seal!
During transport, the release pins on couplings with thumb buttons are often touched.As a result, the thumb button may be in the upper position, partially covering the opening.Please make sure to bring the thumb button to the lower position before connecting the plug!
Original CPC product from the USA. No Chinese imitation!
Tip
Repair kit for fuel pump quick coupling brass replacement for BMW R 1200 R RT GS K 1200
€45.95*
Repair Kit for Fuel Pump
CPC Quick Coupling
Spare Part for Fuel Pump e.g. R1200GS R1200R
R1200RT K1200....
see last image
This repair kit can be used to repair a leaking or broken connection on the fuel pump. Original CPC with fuel-resistant rubber rings!
Quick and easy installation.
Scope of delivery:
1 x CPC coupling nut part plastic with shut-off, 3/8" NPT thread, FKM seal
1 x CPC angled connector brass chrome-plated with shut-off, 3/8" hose nozzle, FKM seal
Attention important notes:CPC recommends for tapered threads:Teflon tape or liquid sealant for thread sealing!Tighten the coupling by hand and then tighten it with a wrench for a maximum of 1 – 2 more turns!Never fully screw in the thread!With tapered threads, only the first three threads seal anyway!
During transport, the release pins on couplings with thumb buttons are often touched.As a result, the thumb button is in the upper position, partially covering the opening.Please make sure to bring the thumb button to the lower position before connecting the plug!
Tip
SW-Motech PRO Micro Tank Bag 3-5 l incl. Pro Tank Ring
€150.00*
PRO Micro Tank Bag including Pro Tank Ring suitable for BMW:
R1200GS LC + Adv., R1250GS + Adv., F900XR, F900R, S1000XR, F750GS, F850GS + Adv., R1200R LC, R1250R, R1200RS, R1250RS, R1200RT LC, R1250RT
Subtle and straightforward: The PRO Micro fits almost any tank and securely transports small essentials like vehicle documents and valuables. Like all PRO tank bags, the Micro sits on an EVA plastic base that guarantees high shape stability. With the help of a zipper, the volume of the tank bag can be expanded.
The PRO tank bags offer elegant and timeless design combined with durable materials and thoughtful product features: Ballistic nylon protects the luggage from impacts, wind, and weather. The top made of laminated EVA material gives the bags a distinctive shape and ensures secure hold for smartphone and tablet holders when combined with a MOLLE attachment. The pre-installed guide rail of the upper ring allows for significantly simplified adjustment of the tank bag to the shape of the tank and the ergonomic needs of the rider. This flexibility is only offered by PRO tank bags. In addition, SW-MOTECH provides the patented PRO tank rings made of fiberglass-reinforced plastic, tailored to the motorcycle model. The robust PRO tank ring with magnetic guiding aid secures the PRO tank bags through a mechanical QUICK-LOCK latch. This allows the tank bags to be attached or removed with just one hand movement.
Volume expansion via zipper from 3 to 5 liters
To attach the PRO tank bag, you need the appropriate PRO tank ring for your motorcycle model.
Magnetic guiding aid in the PRO tank ring for easy attachment
Pre-mounted guide rail of the upper ring for ergonomic adjustment of the tank bag
Top and bottom of the tank bag made of laminated and shape-stable EVA material
Made of robust and particularly UV-resistant 1680D ballistic nylon with water-repellent inner coating
MOLLE attachment made of durable Hypalon material on the top for smartphone and tablet holders
Reflective details for better visibility
Mesh pockets inside
Weather protection with included rain cover
Robust carrying handle
Cable pass-through at the front and back
Can be used with cable lock or anti-theft device
Delivery Contents
1 x PRO Micro Tank Bag
1 x PRO Upper Ring
1 x Rain Cover PRO Micro
Installation instructions
Mounting materials
Details
Material: 1680D Ballistic Nylon
Color: black / gray
Dimensions: 27.0 x 20.5 x 11.0 cm
Total Weight: approx. 0.8 kg
Total Volume: 3.0-5.0 l
Note
For mounting on the tank, the appropriate PRO tank ring is required.
The PRO series tank bags are not compatible with EVO tank rings.
PRO Tank Ring
The PRO tank ring perfectly combines the innovative power of two German companies: The proven QUICK-LOCK latch mechanism of the SW-MOTECH tank rings can now be operated even more easily thanks to the magnetic guiding aid of Fidlock technology. We have significantly improved the positioning of the upper ring: The movable upper ring is already pre-mounted with a guide rail on the tank bag, and the tank bag does not need to be drilled. This allows the upper ring to be individually aligned on the guide rail at the bottom of the tank bag. Once the appropriate position is found, the upper ring is securely screwed in place. When switching to another motorcycle, the position of the upper ring can be adjusted accordingly. The magnetic guiding aid, developed by Fidlock, complements the already mature mechanical QUICK-LOCK latch mechanism from SW-MOTECH: The magnets guide the upper ring into the correct position on the tank ring, and the latch clicks securely into place. Thus, the power of the magnets supports the placement of the tank bag. Attach the tank bag with one hand and drive off – the luggage is secure, and it’s also fun. The mechanical latch mechanism secures the tank bag, and the magnets guide the two parts of the ring together. The robust fiberglass-reinforced plastic with its highly precise latch geometry ensures that the tank bag remains firmly in place in all road conditions. The patented PRO tank ring is tailored to the fuel filler neck of the motorcycle model. This ensures the best possible positioning on the tank.
Model-specific adapter ring for the best fit and individual solutions
Easy installation on the fuel filler neck
Magnetic guiding aid in the PRO tank ring for easy attachment
Quick release via pull strap allows removal of the PRO tank bag with one hand
The patented PRO tank ring provides secure hold for PRO tank bags
Easy refueling, fuel cap can be opened as usual
Made of fiberglass-reinforced polyamide
Paint-friendly solution: the tank bag does not rest on the tank
Delivery Contents
1 x PRO Tank Ring
Installation instructions
Mounting materials
Details
Material: fiberglass-reinforced plastic / aluminum
Color: black
Total Weight: approx. 0.1 kg
Tip
Touratech Crash Bars Stainless Steel for BMW F850GS/F750GS
€329.90*
The crash bar is made from high-quality, electropolished stainless steel and expands the range of use for your adventure motorcycle. The two-part crash bar has been positioned as closely as possible to the vehicle to harmoniously integrate it into the existing vehicle design. Its special construction ensures optimal force distribution and largely protects not only the radiator but also the tank and fairing from damage. The crash bar is easy to install, resistant to rust, and easy to maintain.