The wider and longer enduro footpegs provide better vehicle control off-road while allowing unrestricted operation of the shift and brake levers. More grip and slip-resistant stance. Better vehicle control. Advantages when off-road riding while standing. Delivery includes left enduro footpeg.

The wider and longer enduro footpegs provide better vehicle control off-road while allowing unrestricted operation of the shift and brake levers. More grip and slip-resistant stance. Better vehicle control. Advantages when off-road riding while standing. Scope of delivery: Enduro footpeg right

Foot Brake Lever ExtensionSW-MOTECH manufactures this foot brake lever extension from machined aluminum, designed to fit the original foot brake lever of the BMW F 850 GS.SW-MOTECH produces the extensions from machined, high-strength aluminum alloy with a black anodized finish and a stainless steel footplate. For optimal ergonomic adjustment, the height of the brake lever footplate can be set in two stages of 22 or 27 millimeters.The foot brake lever extension is ideal for off-road riding: it complements the original brake lever footplate and ensures a secure, well-controlled press on the brake. The extension allows for both a widening and an increase in the contact area. This provides more safety and better control of the rear brake.When riding off-road, one often switches between sitting and standing. In a standing position, the knee angle changes, and the foot can exert less pressure on the small pedal. By increasing the contact area, the foot is angled more and can easily reach and control the brake lever even while standing. The height can be adjusted in two different stages.In addition to the height increase, the foot brake lever extension features a widened contact area. This is equipped with a textured surface, providing better grip on dirty or wet lever surfaces.To complement the original brake lever footplateIncreased and wider contact areaBetter grip thanks to the textured surface – even in wet and dirty conditionsHeight increase of the brake lever footplate by 22 or 27 millimetersDelivery Contents1 x Foot Brake Lever ExtensionInstallation instructionsMounting materialsDetailsMaterial: Aluminum / Stainless SteelSurface: AnodizedColor: Black / SilverTotal Weight: Approx. 0.1 kgApproval NoticeThis product does not require approval. Therefore, it does not need any certification marks, expert opinions, or general operating permits. The information in the installation instructions must be observed.

Touratech WORKS stainless steel footpegs. The best that Touratech has to offer for your boots. Specifically developed according to the requirements of the Touratech Works Racing Team. The 52 x 90 mm wide boot-friendly 4mm thick stainless steel claw profile provides the optimal combination of grip and self-cleaning with its special shape. Due to the rounded edges, the soles of the boots are not damaged, and the open design ensures that mud and stones fall away from under the boots through the footpegs, allowing for a secure grip on the peg. The slim design and the bevel towards the outside increase ground clearance, which is particularly advantageous when navigating deep ruts compared to regular enduro footpegs or standard products.The Touratech Works footpegs have been specifically reinforced at the mounting point, making them significantly more resistant to impacts. Visually, the Works products are also a highlight. Shot-blasted stainless steel with a special laser engraving characterizes this product and visually showcases its noble origin from extreme enduro sports.- 52mm wide boot-friendly 4mm thick stainless steel claw profile- optimal combination of grip and self-cleaning- increased ground clearance due to slimmer design- significantly more resistant to impacts- reinforced mounting- refined with shot-blasted surface and laser engravingIncludes ABE. (Extension for BMW F900GS in preparation)

Touratech WORKS stainless steel footpegs. The best that Touratech has to offer for your boots. Specifically developed according to the requirements of the Touratech Works Racing Team. The 52 x 90 mm wide boot-friendly 4mm thick stainless steel claw profile provides the optimal combination of grip and self-cleaning with its special shape. Due to the rounded edges, the soles of the boots are not damaged, and the open design ensures that mud and stones fall away from under the boots through the footpegs, allowing for a secure grip on the peg. The slim design and the bevel towards the outside increase ground clearance, which is particularly advantageous when navigating deep ruts compared to regular enduro footpegs or standard products.The footpegs are 20 mm lower than the original pegs (without rubber insert).The Touratech Works footpegs have been specifically reinforced at the mount and are therefore significantly more resistant to impacts. Visually, the Works products are also a highlight. Shot-blasted stainless steel with a special laser engraving characterizes this product and visually showcases its noble origin from extreme enduro sports.- 52mm wide boot-friendly 4mm thick stainless steel claw profile- optimal combination of grip and self-cleaning- increased ground clearance due to slimmer design- significantly more resistant to impacts- reinforced mount- refined with shot-blasted surface and laser engravingIncludes ABE. (Extension for F900GS in preparation)